MODEL RANGE - TSC5L5

The TSC 5L5 Transducer Display

FEATURES

• 5 Channel dual analogue limit control, selected locally or remotely with latching and reset.

• 4.5 Digit (back lit) Programmable display with many math features (max, min, av, etc).

• Control of external processes by dual relays both 24 vdc output and volt free contacts.

• Special pulsed 24 volt output for Go process control.

• Logic outputs and remote limit indication signaling for LED’s.

• Peak or First Peak with trigger level and reset time (adjustable) controls.

• Mains powered. Powers and displays any TSC transducer or similar products.

• RS232 or 485 and analog (high level) signal outputs.

SPECIFICATION

Pulsed output for GO (pass): 24volt@200mA,d.c. Timed to operate for 0.5 secs after 0.5 secs of low limit operating

Limits Digital: 2(High & Low) settable hysterisis with buzzer

Math Functions: Maximum, minimum, readings since power up. Average, 2, 4 or 8 sample, programmable.

Torque Signal output Bipolar: +/- 1V dc for rated capacity

Output : RS232 or RS485 

Decimal point Ranges: 0.0001 1 to 19999

Operating Temperature Range: 0 deg. C to +50 deg. C

Input Power Requirements: 230 V AC 50Hz 1Amp

Accuracy: +/- 0.01% of FSD 1% of RDG from 10-110% FRO

Linearity: +/- 1 count

Display: 4.5 digit LCD 10 mm high, back lit. Programmable dec point

Display Sample Rate: 4 per second

Frequency Response Analog output: Better than 2.5KHz

Temperature Coefficient: 30 p.p.m per degree C

Alarm Limits Analog: 5 sets of 2 ( High & Low) with LED indicators each set (channel) selectable by switch (local) or remote by microswitch

Alarm Limits Analog Range: 5%-180% of FSD. Accuracy1% of rdg. Low Limit has 24v d.c@200mA out. Energised below limit set. High limit has change over, volt free contacts. max 50volts @ 0.5 Amp.

The TSC 5L5 Transducer Display provides a complete instrument for the display and powering of TSC’s and other manufacturer’s strain gauge torque transducers’. It has Peak and First peak selectable operations. The first peak trigger level and reset time are settable. Max, min average and filter response are additional facilities and are programmable via front panel buttons. In addition it has 5 limit detector channels enabling multi levels of low, Pass and High limits to be set. These limits are selectable locally by a manual switch or remotely by micro switches and will control external processes. The lower limit outputs a 24 volt DC supply to energize solenoids when the torque signal is below the low limit. The high limit has make and break, volt free relay contacts. The limits can be latched and reset locally or remotely. For remote indication of limit state, logic signals are provided which are capable of driving low power L.E.D’s. A special facility for control of a solenoid for Go, No-go process control using an on board 24 Volt, 200mAmp(max) DC power supply sends a 0.5 second pulse for solenoid operation when the lower limit but not the upper limit is exceeded after a 0.5 second dwell period. The applied force direction to the transducer, is sensed and displayed by the CW/CCW L.E.D indicators (clockwise and anticlockwise). The TSC5L5 also provides the amplified interface for analog to digital converter input for Computers or to drive X Y - T plotters. It has RS 232 and option for RS485 output. The TSC5L5 is mains powered, selectable for the supply voltage required.

Applications: Torque power tool control using remote socket tray to select torque limit required for production fastening processes; Process control; Research and Development